Description |
Eagle 2KTop is an high quality, two components, normal-set cementitious mortar. It can repair and give a new finish to old and damaged concrete surfaces. This mortar is specially formulated to level old concrete surfaces, horizontally or vertically. Thicknesses that can vary from 1 mm (1/32”) to 12 mm (1/2”) in one application, interior or exterior uses. The liquid polymer included in the packaging, contributes greatly to concrete protection by improving waterproof qualities and resistance against abrasion, freeze and thaw cycles and de-icing salts. |
Surface Preparation |
All surfaces shall be structurally sound, clean and free from traces of dust, oil, grease and must also be exempt of acids, alkalis, chemical cleaning agent or any other material that could reduce adhesion. All concrete substrates shall be completely cured and at least 28 days old. They must be roughened to offer good bonding. Saturate concrete surface with clean water few hours before repairs leaving no excess water. Apply mortar when surface is dry again. The use of Eagle Prime Plus as primer is a good alternative to concrete water saturation. Ambient, surface and product temperature must be superior than 10ºC (50ºF) and lower than 35ºC (95ºF) during the installation and for the first 24 hours. Avoid working under intense or midday sun. |
Mixing |
In a clean container, pour 4/5 of latex and gradually add Eagle 2KTop powder while mixing with a low-speed drill and a mixer. For 6 mm to 12 mm (1/4” to ½”) application, use as is; for thinner applications, add the remaining of latex. Blend for 2 to 3 minutes scraping recipient walls and paddle to obtain a homogeneous mixture lump-free consistency. Slake for 5 minutes and mix again for 1 minute. Proceed to application and finishing. |
Curing |
Eagle 2KTop takes 2 to 5 hours to dry, depending on its consistency and ambient temperatures. May also vary according to temperature and humidity level. Protect fresh surface from rain, sun and wind but without any contact with the surface to alter the finish. Wait 24 hours prior to allow light traffic. |
Cleanning |
Clean working tools and hands with water while product is still fresh. |
Package |
This product is available in 6 kg and 22.7 kg pail. |
Shelf Life |
Store in a dry and fresh area. Shelf life is 12 months in its original non-opened container. |
Technical Data Table |
CARACTERISTICS |
CURE |
EAGLE 2KTOP (18% Latex) |
EAGLE 2KTOP (21% Latex) |
Pot life |
|
> 1 :00 hour |
> 1 :00 hour |
Set time initial / final ASTM C-191 |
|
1 :30 hour / 5 :00 hours |
2 :15 hours / 5 :40 hours |
Density ASTM C-185 |
|
1.79 kg/l |
1.88 kg/l |
Compressive strength ASTM C-109 |
24 hours
7 days
28 days |
6 MPa (870 PSI)
24 MPa (3481PSI)
28 MPa (4061 PSI) |
3.5 MPa (507 PSI)
16 MPa (2320 PSI)
20MPa (2900 PSI) |
Flexural strength ASTM C-348 |
24 hours
7 days
28 days |
2.5 MPa (363 PSI)
9.5 MPa (1378 PSI)
12.5 MPa (1813 PSI) |
4.5 MPa (652 PSI)
10.5 MPa (1523 PSI)
12.0 MPa (1740 PSI) |
Pull-out strength on concrete CSA A23.2-6B |
7 days
28 days |
1.00 MPa (145 PSI)
1.11 MPa (161 PSI) |
1.02 MPa (148 PSI)
1.26 MPa (183 PSI) |
Coverage per kg of product |
|
0.5 m² (5.4 ft²) for 2 mm (1/16”) thickness |
0.5 m² (5.4 ft²) for 2 mm (1/16”) thickness |
* Drying Time depend of surface porosity and temperature |
Reviews
There are no reviews yet.